1

**PreenFM2 / FareyPreenFM2 little programming tool**

« **on:**April 18, 2017, 07:31:08 AM »

hi everyone

i only a have a sec to write this, so apologies for brevity. am loving the PreenFM2.. i've just uploaded a little Farey PreenFM2 programmer here to github, brief info below. its written in Processing so anyone should be able to run it if you get a copy of Processing. hope folks find it useful, its a pretty early version..

cheers

dave

https://github.com/noyzelab/FareyPreenFM2

readme ->

FareyPreenFM2

Farey sequence family ratios generator/programmer for the PreenFM2 synthesizer

David Burraston

April 2017

http://www.noyzelab.com

commands =>

'z': //decrement farey order 'x': //increment farey order

'c' : //decrement family index 'v' : //increment family index

'b': // decrement carrier (op1) family member

'n': // increment carrier (op1) family member

'm': // decrement carrier (op2) family member

',': // increment carrier (op2) family member

'r': // randomize all farey parameters

's': // send all integer ratios (C) to preenfm op1&3 pair and op2&4 pair

'1' : // send intetger ratios to preenfm op1&3 pair

'2' : // send intetger ratios to preenfm op1&3 pair

'f': // send as floating point ratios (FLC) to preenfm op1&3 pair and op2&4 pair modulator normalised to 1.00

'!' : // send as floating point ratios to preenfm op1&3 pair modulator normalised to 1.00

'@' : // send as floating point ratios to preenfm op2&4 pair modulator normalised to 1.00

'g': // send as floating point ratios to preenfm (FLM) op1&3 pair and op2&4 pair carrier normalised to 1.00

'-' : // send as floating point ratios to preenfm op1&3 pair carrier normalised to 1.00

'=' : // send as floating point ratios to preenfm op2&4 pair carrier normalised to 1.00

'k': // do a minimal voice reconfig for receiving params: sets ALG4, filter off & gain 1.0, IM1&2 and velocity response to 8, mix 1 & 2 to 1.0, IM3&4 off and velocity to 0, op1,2,3,4 to sin with keyboard tracking

'w' : // set waves 1 to 4 to sine & keytrking to kybd

'4' : // set ALG to 4

<========= ** The maximum frequency ratio setting on the PreenFM2 is 16, ** so attempting to send values higher than 16 will be clipped at 16 by PreenFM2 .. ! <=========

NOTES:

The choice of Carrier:Modulator (C:M) frequency ratio is an interesting area of research, because it is one of the fundamental aspects of FM programming. Farey Sequences for FM programming were introduced in the classic text by Barry Truax: Organizational Techniques for C:M Ratios in Frequency Modulation. http://www.sfu.ca/~truax/

FareyPreenFM2 is designed to make two carrier/modulator pairs based on the Farey Sequence, and so it uses Algorithm 4 .. so you could also use it with Algorithm 2 for programming Op1/Op2, or Alogrithm 12, or anyhow you like of course.. at the moment its only really designed for generating up to 2 C:M pairs. When/if I get time I'll hope to add more commands for mapping with the other FM algorithms and higher order Farey Sequences..

In order to get the best from this program please read up on Farey Sequences for FM programming, I did an article here and there are lots of places to read further : http://noyzelab.blogspot.com/2016/04/farey-sequence-tables-for-fm-synthesis.html

I would recommend starting from an init patch or something like that first, i.e. turn off all matrix modulation, sin waves for ops etc etc while you are researching Farey Sequence ratios and then try loading in existing patches and modifying them, remember to set Algorithm to 4 for the ratios to be set up as C:M pairs. You can use number key '4' to setup ALG4 on PreenFM2, or do a slightly larger reconfig of the voice by pressing 'k' (see key commands above). Press 'r' to randomize your choice of Farey Sequence pair etc. AND remember that nothing gets sent to the PreenFM2 unless you send it! e.g. press '1' to send the integer ratio diplayed in the left C:M pair boxes etc.

Family index refers to which C:M pair from a common M value (Family Order). Not all Farey C:M ratios have multiple common M values e.g. Family Order 4 has only one member 1:4, but Family Order 9 has three members : 1:9, 2:9 and 4:9.

Each Family ratio can then be used to obtain a family of integer ratios sharing the same spectral identity. These are the vertical listings on the screen, C+, C- are the standard integer versions as defined in the research, and FLC and FLM are versions made into floating point values using 2 simple methods I made up so I can;t vouch for their spectral validity.. :]

FLC = C+/M:M/M & C-/M:M/M i.e. divide by modulator, resulting in constant modulator values of 1.0 MLC = C+/C+:M/C+ & C-/C-:M/C- i.e. divide by carrier,resulting in constant carrier values of 1.0

You can also use this program for generating ratios to manually program into other FM synths e.g. TX81Z, DX7 etc.

BUT: this program was written in Processing : https://processing.org/ and at the moment the sysex in Processing, and hence.. .. Java.. .. , is pretty much non-existant for OS X!! I have tried the suggested method from MIDIBus :

http://www.smallbutdigital.com/projects/themidibus/

but it don;t work on my machine.. so at the moment sysex only works under Windows in Processing for me.. ! So I am not including any MIDI sysex until I can get it going on OS X. There also doesn;t seem to be much key repeat action on my machine, so this may or may not work for the key commands..

i only a have a sec to write this, so apologies for brevity. am loving the PreenFM2.. i've just uploaded a little Farey PreenFM2 programmer here to github, brief info below. its written in Processing so anyone should be able to run it if you get a copy of Processing. hope folks find it useful, its a pretty early version..

cheers

dave

https://github.com/noyzelab/FareyPreenFM2

readme ->

FareyPreenFM2

Farey sequence family ratios generator/programmer for the PreenFM2 synthesizer

David Burraston

April 2017

http://www.noyzelab.com

commands =>

'z': //decrement farey order 'x': //increment farey order

'c' : //decrement family index 'v' : //increment family index

'b': // decrement carrier (op1) family member

'n': // increment carrier (op1) family member

'm': // decrement carrier (op2) family member

',': // increment carrier (op2) family member

'r': // randomize all farey parameters

's': // send all integer ratios (C) to preenfm op1&3 pair and op2&4 pair

'1' : // send intetger ratios to preenfm op1&3 pair

'2' : // send intetger ratios to preenfm op1&3 pair

'f': // send as floating point ratios (FLC) to preenfm op1&3 pair and op2&4 pair modulator normalised to 1.00

'!' : // send as floating point ratios to preenfm op1&3 pair modulator normalised to 1.00

'@' : // send as floating point ratios to preenfm op2&4 pair modulator normalised to 1.00

'g': // send as floating point ratios to preenfm (FLM) op1&3 pair and op2&4 pair carrier normalised to 1.00

'-' : // send as floating point ratios to preenfm op1&3 pair carrier normalised to 1.00

'=' : // send as floating point ratios to preenfm op2&4 pair carrier normalised to 1.00

'k': // do a minimal voice reconfig for receiving params: sets ALG4, filter off & gain 1.0, IM1&2 and velocity response to 8, mix 1 & 2 to 1.0, IM3&4 off and velocity to 0, op1,2,3,4 to sin with keyboard tracking

'w' : // set waves 1 to 4 to sine & keytrking to kybd

'4' : // set ALG to 4

<========= ** The maximum frequency ratio setting on the PreenFM2 is 16, ** so attempting to send values higher than 16 will be clipped at 16 by PreenFM2 .. ! <=========

NOTES:

The choice of Carrier:Modulator (C:M) frequency ratio is an interesting area of research, because it is one of the fundamental aspects of FM programming. Farey Sequences for FM programming were introduced in the classic text by Barry Truax: Organizational Techniques for C:M Ratios in Frequency Modulation. http://www.sfu.ca/~truax/

FareyPreenFM2 is designed to make two carrier/modulator pairs based on the Farey Sequence, and so it uses Algorithm 4 .. so you could also use it with Algorithm 2 for programming Op1/Op2, or Alogrithm 12, or anyhow you like of course.. at the moment its only really designed for generating up to 2 C:M pairs. When/if I get time I'll hope to add more commands for mapping with the other FM algorithms and higher order Farey Sequences..

In order to get the best from this program please read up on Farey Sequences for FM programming, I did an article here and there are lots of places to read further : http://noyzelab.blogspot.com/2016/04/farey-sequence-tables-for-fm-synthesis.html

I would recommend starting from an init patch or something like that first, i.e. turn off all matrix modulation, sin waves for ops etc etc while you are researching Farey Sequence ratios and then try loading in existing patches and modifying them, remember to set Algorithm to 4 for the ratios to be set up as C:M pairs. You can use number key '4' to setup ALG4 on PreenFM2, or do a slightly larger reconfig of the voice by pressing 'k' (see key commands above). Press 'r' to randomize your choice of Farey Sequence pair etc. AND remember that nothing gets sent to the PreenFM2 unless you send it! e.g. press '1' to send the integer ratio diplayed in the left C:M pair boxes etc.

Family index refers to which C:M pair from a common M value (Family Order). Not all Farey C:M ratios have multiple common M values e.g. Family Order 4 has only one member 1:4, but Family Order 9 has three members : 1:9, 2:9 and 4:9.

Each Family ratio can then be used to obtain a family of integer ratios sharing the same spectral identity. These are the vertical listings on the screen, C+, C- are the standard integer versions as defined in the research, and FLC and FLM are versions made into floating point values using 2 simple methods I made up so I can;t vouch for their spectral validity.. :]

FLC = C+/M:M/M & C-/M:M/M i.e. divide by modulator, resulting in constant modulator values of 1.0 MLC = C+/C+:M/C+ & C-/C-:M/C- i.e. divide by carrier,resulting in constant carrier values of 1.0

You can also use this program for generating ratios to manually program into other FM synths e.g. TX81Z, DX7 etc.

BUT: this program was written in Processing : https://processing.org/ and at the moment the sysex in Processing, and hence.. .. Java.. .. , is pretty much non-existant for OS X!! I have tried the suggested method from MIDIBus :

http://www.smallbutdigital.com/projects/themidibus/

but it don;t work on my machine.. so at the moment sysex only works under Windows in Processing for me.. ! So I am not including any MIDI sysex until I can get it going on OS X. There also doesn;t seem to be much key repeat action on my machine, so this may or may not work for the key commands..