Messages

91

preenfm2 and preenfm3 / Re: 1.B2 Firmware January 26th

« on: January 28, 2014, 03:47:18 PM »

hi bpm has odd behavior in arp below 120 slows v slowly above 120 speeds up v fast

92

preenfm2 and preenfm3 / Re: 1.B2 Firmware January 26th

« on: January 28, 2014, 01:06:28 PM »

works fine

93

preenfm2 and preenfm3 / Re: 1.b* Beta Firmware

« on: January 22, 2014, 05:29:53 PM »

hi think i have found a bug:- arp direction bug, it fails to change properly when in latch mode or when holding down a note.
Many Thanks

94

preenfm2 and preenfm3 / Re: 1.b* Beta Firmware

« on: January 22, 2014, 11:10:32 AM »

hi this firmware is great, the arp and filter are brilliant fun. when i turn up voices on one instrument it makes all the other instruments more quiet. eg all instruments on one voice each, increase the voices of one and all decrease in volume. and also on filter mix there is a volume spike when pan is set to 0.50,
also would it be possible to link the step seq to the arp pattern section and add direction played( as in shruthi) in the arp direction settings

95

preenfm2 and preenfm3 / Re: OLED case SVG issue?

« on: January 15, 2014, 12:05:19 PM »

thanks Xavier, low-fi method, permanent marker then wipe excess off with a cloth

96

preenfm2 and preenfm3 / Re: OLED case SVG issue?

« on: January 14, 2014, 12:28:00 PM »

i initially had this problem with razorlab something wrong with the svg file have already sent them a new one

97

preenfm2 and preenfm3 / Re: PCB Only/BOM problem reports

« on: January 03, 2014, 11:45:54 AM »

hi these are the encoders on ebay
http://www.ebay.co.uk/itm/121195339728?var=420187086302&ssPageName=STRK:MEWNX:IT&_trksid=p3984.m1497.l2649
any good?

98

preenfm2 and preenfm3 / Re: PCB Only/BOM problem reports

« on: December 30, 2013, 01:31:54 PM »

hello also i have somme 1n4004 diodes at home could i use one of these instead of the 1n4001 in the bom

99

preenfm2 and preenfm3 / Re: PCB Only/BOM problem reports

« on: December 30, 2013, 01:28:00 PM »

hi again can i use encoders with 20 dents instead of 24, will it cause any problems

100

preenfm2 and preenfm3 / Re: Firmware: PreenFM2 Bug report

« on: December 23, 2013, 05:08:21 PM »

hi think i found a bug. when i have all 4 instruments loaded and playing a midi file from pc, if i alter IM in one instrument it changes others instruments IM too? hope that makes sense. also when i chain a shruthi from midi out in preen and play the same midi file from pc the shruthi loses sync over time.

101

preenfm2 and preenfm3 / Re: Firmware: PreenFM2 Bug report

« on: December 22, 2013, 01:55:03 PM »

hi maybe you could have note as a destination in the matrix so source can be sequence.?

102

preenfm2 and preenfm3 / Re: Firmware: PreenFM2 Bug report

« on: December 21, 2013, 06:49:07 PM »

hello gain, would it be possible to allow the sequencer to trigger notes on the preen like a drum machine.

103

preenfm2 and preenfm3 / Re: PCB Only/BOM problem reports

« on: December 17, 2013, 01:44:57 PM »

so just to clarify, is it ok to use encoders with push switch

104

preenfm2 and preenfm3 / Re: Firmware: PreenFM2 Bug report

« on: December 16, 2013, 03:57:32 PM »

hi xavier just uploaded new firmware k but cannot see combo files preen 1 files working fine

105

preenfm2 and preenfm3 / Re: Using the PreenFM2

« on: December 05, 2013, 10:39:06 PM »

hi was wondering if it would be possible to hear frequency changes real time while playing test note. i can only hear changes when a new note is played.
cheers