31
preenfm2 and preenfm3 / Re: PreenFM3 case options
« on: June 17, 2021, 07:00:54 PM »
Great! They look really nice!
Thanks a lot!
Phil
Thanks a lot!
Phil
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
32
preenfm2 and preenfm3 / Re: PreenFM3 case options
« on: April 28, 2021, 12:39:18 PM »
Fantastic! Thank you!
33
preenfm2 and preenfm3 / Re: PreenFM3 case options
« on: April 25, 2021, 01:35:43 PM »
I have zero experience with acrylic laser cutting and didn’t know it might be so cheap.
I think I saw that someone on this forum has created files for a complete PreenFM3 acrylic case. I didn’t give it much attention, as I was primarily looking for a solution to go with the faceplate provided with your (Xavier's) kit.
It would definitely be helpful to people like me to have alternative case solutions to 3D printing.
I think I saw that someone on this forum has created files for a complete PreenFM3 acrylic case. I didn’t give it much attention, as I was primarily looking for a solution to go with the faceplate provided with your (Xavier's) kit.
It would definitely be helpful to people like me to have alternative case solutions to 3D printing.
34
preenfm2 and preenfm3 / Re: PreenFM3 case options
« on: April 24, 2021, 10:29:16 AM »
Thanks for your replies!
I emailed Van Daal two days ago and am waiting for a reply.
I was wondering about online Plexi glass / acrylic laser cutting services but assumed that might be expensive as well. I will check prices!
I’m also considering having just the back plate 3D printed, which would cost about €35 by itself and then buy an acrylic sheet and cut the easier side and bottom plates myself. I think that might be a solution for me.
Phil
I emailed Van Daal two days ago and am waiting for a reply.
I was wondering about online Plexi glass / acrylic laser cutting services but assumed that might be expensive as well. I will check prices!
I’m also considering having just the back plate 3D printed, which would cost about €35 by itself and then buy an acrylic sheet and cut the easier side and bottom plates myself. I think that might be a solution for me.
Phil
35
preenfm2 and preenfm3 / Re: PreenFM3 case options
« on: April 22, 2021, 11:32:49 AM »
Thanks for your reply!
I have not seen a black case for the PreenFM3 on Van Daal's website. Maybe an option for the black case will pop up when the cases are back in stock. I will keep an eye on that!
Thanks!
Phil
I have not seen a black case for the PreenFM3 on Van Daal's website. Maybe an option for the black case will pop up when the cases are back in stock. I will keep an eye on that!
Thanks!
Phil
36
preenfm2 and preenfm3 / PreenFM3 case options
« on: April 21, 2021, 10:21:09 AM »
Hi,
I’m interested in building a PreenFM3 using the kit from Xavier with faceplate but without the rest of the case.
Commercial services for 3D printing the rest of the case are expensive at around €140 in Germany.
Is there an inexpensive solution for side and back panels to go with the faceplate provided in Xavier's kit?
I know of the Van Daal metal case but would much prefer a black enclosure.
I’m completely new to the DIY synth world and would be glad for any advice about case options!
Thanks!
Phil
I’m interested in building a PreenFM3 using the kit from Xavier with faceplate but without the rest of the case.
Commercial services for 3D printing the rest of the case are expensive at around €140 in Germany.
Is there an inexpensive solution for side and back panels to go with the faceplate provided in Xavier's kit?
I know of the Van Daal metal case but would much prefer a black enclosure.
I’m completely new to the DIY synth world and would be glad for any advice about case options!
Thanks!
Phil