1
preenfm2 and preenfm3 / Re: Some new hacks
« on: May 12, 2020, 02:15:59 PM »
the delay sounds awsome. not sure i understand new things number 2. does it play a sequence of drums or just very short envelopes. thanks
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
2
preenfm2 and preenfm3 / Re: New beta firmware 2.00 beta 1 (August 28th)
« on: September 28, 2015, 01:57:25 PM »
i dont think you lose real resolution its just the displays limitations
3
preenfm2 and preenfm3 / Re: New beta firmware 2.00 beta 1 (August 28th)
« on: September 01, 2015, 01:50:12 PM »
absolutely awesome great work xavier
4
preenfm2 and preenfm3 / Re: Paraphonic vs Polyphonic (an other beta firmware included)
« on: August 18, 2015, 01:30:37 AM »
this sounds great, nice work:)
5
preenfm2 and preenfm3 / Re: My Hacks...
« on: January 06, 2015, 08:44:08 PM »
cheers will try it out tonight 
6
preenfm2 and preenfm3 / Re: Patches... (Funky Bank 2 - Boogalu)
« on: October 22, 2014, 12:05:21 AM »
excellent work
7
preenfm2 and preenfm3 / Re: Midi In/Out V's USB etc?
« on: September 28, 2014, 11:57:20 AM »
yes it works just the same
8
preenfm2 and preenfm3 / Re: Last firmware 1.05 : randomizer
« on: September 17, 2014, 10:41:01 AM »
hello there it is awsome. you configure the randomiser with p1- p4 then randomise with any one of the buttons on the left then confirm with button 7 so you can edit further.
9
preenfm2 and preenfm3 / Re: background noise when i use usb as power supply
« on: September 12, 2014, 12:21:24 PM »
cheers for the suggestions will try them out not a big problem tho can just use external 9v power supply
10
preenfm2 and preenfm3 / background noise when i use usb as power supply
« on: September 11, 2014, 01:20:21 PM »
love the preen most usefull of all my synths but seem to get noise if i use usb as a power supply. no noise if i use external 9v. is there any thing you can suggest, tried 3 different usb cable with and without sheilding no change. thanks
11
preenfm2 and preenfm3 / Re: Last firmware 1.05 : randomizer
« on: September 10, 2014, 12:44:20 AM »
excellent work, randomizer is great fun
12
preenfm2 and preenfm3 / Re: low output
« on: September 08, 2014, 07:27:47 PM »
solved! my fault used wrong op amp only 1 channel
TLV2451CP
TLV2451CP
13
preenfm2 and preenfm3 / Re: low output
« on: September 08, 2014, 05:13:05 PM »
have got near enough 0v on pin 1 and 5v on pin 8, cheers. are there any schematics so i can test continuity.
14
preenfm2 and preenfm3 / low output : solved
« on: September 08, 2014, 02:59:41 PM »
hi there just put another preen together today and have a low noisy output? which components and areas of the pcb should i check first.
thanks
thanks
15
preenfm2 and preenfm3 / Re: More Cowbell
« on: August 29, 2014, 01:06:23 PM »
you can dump the current patch to pc using save_syx_Send patch, obviously using c6 or similar. and you can load these patches to preenfm2 using c6 to send it.