Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - martindunne

Pages: [1] 2 3 ... 8
1
preenfm2 and preenfm3 / Re: Some new hacks
« on: May 12, 2020, 02:15:59 PM »
the delay sounds awsome. not sure i understand new things number 2. does it play a sequence of drums or just very short envelopes. thanks

2
preenfm2 and preenfm3 / Re: New beta firmware 2.00 beta 1 (August 28th)
« on: September 28, 2015, 01:57:25 PM »
i dont think you lose real resolution its just the displays limitations

3
preenfm2 and preenfm3 / Re: New beta firmware 2.00 beta 1 (August 28th)
« on: September 01, 2015, 01:50:12 PM »
absolutely awesome great work xavier

4
this sounds great, nice work:)

5
preenfm2 and preenfm3 / Re: My Hacks...
« on: January 06, 2015, 08:44:08 PM »
cheers will try it out tonight :)

6
preenfm2 and preenfm3 / Re: Patches... (Funky Bank 2 - Boogalu)
« on: October 22, 2014, 12:05:21 AM »
excellent work

7
preenfm2 and preenfm3 / Re: Midi In/Out V's USB etc?
« on: September 28, 2014, 11:57:20 AM »
yes it works just the same

8
preenfm2 and preenfm3 / Re: Last firmware 1.05 : randomizer
« on: September 17, 2014, 10:41:01 AM »
hello there it is awsome. you configure the randomiser with p1- p4 then randomise with any one of the buttons on the left then confirm with button 7 so you can edit further.

9
preenfm2 and preenfm3 / Re: background noise when i use usb as power supply
« on: September 12, 2014, 12:21:24 PM »
cheers for the suggestions will try them out not a big problem tho can just use external 9v power supply :)

10
preenfm2 and preenfm3 / background noise when i use usb as power supply
« on: September 11, 2014, 01:20:21 PM »
love the preen most usefull of all my synths but seem to get noise if i use usb as a power supply. no noise if i use external 9v. is there any thing you can suggest, tried 3 different usb cable with and without sheilding no change. thanks

11
preenfm2 and preenfm3 / Re: Last firmware 1.05 : randomizer
« on: September 10, 2014, 12:44:20 AM »
excellent work, randomizer is great fun

12
preenfm2 and preenfm3 / Re: low output
« on: September 08, 2014, 07:27:47 PM »
solved!  my fault used wrong op amp only 1 channel
TLV2451CP

13
preenfm2 and preenfm3 / Re: low output
« on: September 08, 2014, 05:13:05 PM »
have got near enough 0v on pin 1 and 5v on pin 8, cheers. are there any schematics so i can test continuity.

14
preenfm2 and preenfm3 / low output : solved
« on: September 08, 2014, 02:59:41 PM »
hi there just put another preen together today and have a low noisy output? which components and areas of the pcb should i check first.
thanks

15
preenfm2 and preenfm3 / Re: More Cowbell
« on: August 29, 2014, 01:06:23 PM »
you can dump the current patch to pc using save_syx_Send patch, obviously using c6 or similar. and you can load these patches to preenfm2 using c6 to send it.

Pages: [1] 2 3 ... 8