16
preenfm2 and preenfm3 / Re: Bad power supply with high voltage.
« on: November 13, 2014, 11:29:52 PM »
It's ok now i have found the correct version in my hard disk.
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Pages: 1 [2]
17
preenfm2 and preenfm3 / Re: Bad power supply with high voltage.
« on: November 13, 2014, 11:25:02 PM »
v 0.1 ...
but i can't reach dfu.org !!
but i can't reach dfu.org !!
18
preenfm2 and preenfm3 / Re: Bad power supply with high voltage.
« on: November 13, 2014, 11:18:40 PM »
Problem with dfu
C:\Documents and Settings\Papa Ours.MINIMOI\Mes documents\Téléchargements\preenf
m>dfu-util -a0 -d 0x0483:0xdf11 -D p2_boot_1.11.bin -R -s 0x8000000
dfu-util - (C) 2007-2008 by OpenMoko Inc.
This program is Free Software and has ABSOLUTELY NO WARRANTY
dfu-util: invalid option -- s
Usage: dfu-util [options] ...
-h --help Print this help message
-V --version Print the version number
-l --list List the currently attached DFU capable USB devi
ces
-d --device vendor:product Specify Vendor/Product ID of DFU device
-p --path bus-port. ... .port Specify path to DFU device
-c --cfg config_nr Specify the Configuration of DFU device
-i --intf intf_nr Specify the DFU Interface number
-a --alt alt Specify the Altsetting of the DFU Interface
by name or by number
-t --transfer-size Specify the number of bytes per USB Transfer
-U --upload file Read firmware from device into <file>
-D --download file Write firmware from <file> into device
-R --reset Issue USB Reset signalling once we're finished
C:\Documents and Settings\Papa Ours.MINIMOI\Mes documents\Téléchargements\preenf
m>dfu-util -a0 -d 0x0483:0xdf11 -D p2_boot_1.11.bin -R -s 0x8000000
dfu-util - (C) 2007-2008 by OpenMoko Inc.
This program is Free Software and has ABSOLUTELY NO WARRANTY
dfu-util: invalid option -- s
Usage: dfu-util [options] ...
-h --help Print this help message
-V --version Print the version number
-l --list List the currently attached DFU capable USB devi
ces
-d --device vendor:product Specify Vendor/Product ID of DFU device
-p --path bus-port. ... .port Specify path to DFU device
-c --cfg config_nr Specify the Configuration of DFU device
-i --intf intf_nr Specify the DFU Interface number
-a --alt alt Specify the Altsetting of the DFU Interface
by name or by number
-t --transfer-size Specify the number of bytes per USB Transfer
-U --upload file Read firmware from device into <file>
-D --download file Write firmware from <file> into device
-R --reset Issue USB Reset signalling once we're finished
19
preenfm2 and preenfm3 / Re: Bad power supply with high voltage.
« on: November 13, 2014, 10:53:18 PM »
ok let's go i'm coming back soon :-)
20
preenfm2 and preenfm3 / Re: Bad power supply with high voltage.
« on: November 13, 2014, 10:44:14 PM »
Ok let's go
7805 : Input 10.6 V Output 4.93
LD1117 Input 4,87 Output 3,28
The 7805 is hot and not the second regulator.
It seems correct !
7805 : Input 10.6 V Output 4.93
LD1117 Input 4,87 Output 3,28
The 7805 is hot and not the second regulator.
It seems correct !
21
preenfm2 and preenfm3 / Re: Bad power supply with high voltage.
« on: November 13, 2014, 10:30:45 PM »
No it's the number 2 !
22
preenfm2 and preenfm3 / Re: Bad power supply with high voltage.
« on: November 13, 2014, 10:20:54 PM »
and unfortunaly no sound 
23
preenfm2 and preenfm3 / Re: Bad power supply with high voltage.
« on: November 13, 2014, 09:54:03 PM »
Here's my blank screen :
24
preenfm2 and preenfm3 / Re: Bad power supply with high voltage.
« on: November 13, 2014, 09:44:11 AM »
Hi Xavier,
When i had the wrong power supply it was 18V.
About sound i havn't tested it and the display doesn't change when i turn encoder.
I will post a picture this evening.
When i had the wrong power supply it was 18V.
About sound i havn't tested it and the display doesn't change when i turn encoder.
I will post a picture this evening.
25
preenfm2 and preenfm3 / [SOLVED]Bad power supply with high voltage.
« on: November 13, 2014, 12:21:34 AM »
Hi,
i have made a mistake last night : i have connected a power supply too high in voltage for the preenfm2 first run board.
Now i have a screen with few whites and black squares. Regulator 7805 was very hot. I have tested it and same voltage in input and output.
I have replaced it with a new one. Now i have 10 v in input and 5,2V at output.
But still strange screen with indications.
Where i can find reference voltage to check which components are out of service please ?
Thanks for your help.
i have made a mistake last night : i have connected a power supply too high in voltage for the preenfm2 first run board.
Now i have a screen with few whites and black squares. Regulator 7805 was very hot. I have tested it and same voltage in input and output.
I have replaced it with a new one. Now i have 10 v in input and 5,2V at output.
But still strange screen with indications.
Where i can find reference voltage to check which components are out of service please ?
Thanks for your help.
26
preenfm2 and preenfm3 / Re: Problem with M oHm resistors
« on: December 12, 2013, 11:39:05 PM »
You're right, thanks for the tip, i don't knew that !
27
preenfm2 and preenfm3 / Re: Problem with M oHm resistors
« on: December 12, 2013, 11:26:46 PM »
Xavier, thanks for your quick reply, i have checked few times and it was 11 M and now i measure to make you a photo, and my multimeter say 1 M ... i don't understand 
Let's go !
Let's go !
28
preenfm2 and preenfm3 / [Fixed] Problem with M oHm resistors
« on: December 12, 2013, 10:58:37 PM »
Hi,
i've just received my kit, thanks Xavier !
I'm beginning by the resistors but when i measure the 1 Mohm Resisor, my multimeter say 11 Mohm ...
Is there a problem ?
i've just received my kit, thanks Xavier !
I'm beginning by the resistors but when i measure the 1 Mohm Resisor, my multimeter say 11 Mohm ...
Is there a problem ?
Pages: 1 [2]