1.00 : finally

[martindunne]

hi another suggestion if possible. Is it possible to have a latched arp continue to play while auditioning other presets.

thanks

[Xavier]

hi another suggestion if possible. Is it possible to have a latched arp continue to play while auditioning other presets.
thanks

Good idea...
Preventing latched arp to stop when changing preset would be enough.
I add that on the "Idea" list ;-)

Not sure what will make the arp stop though....

[martindunne]

hello again this might be going too far but is there a way to split the keyboard so that instrument 1 plays lower end and any higher is played by another instrument.

just a thought

cheers

[Xavier]

Hi Marin,

I won't integrate that soon in the engine, but i think there are many tools that can do that for you.
I have a "Graphite 25" small keyboard, and it has zones that have their own midi chanel and can do that very easily.

Or you'll have to tweak the code. MidiDecoder.cpp => midiEventReceived() => case MIDI_NOTE_ON.
If you have some programming notion, you can easily split the keyboard to fit your need.

[martindunne]

hello again

another question, I cannot seem to be able to modulate mix* with free env 1 & 2 or step seq 1/2.

cheers any news on new firmware

thanks again

[Xavier]

hello again
another question, I cannot seem to be able to modulate mix* with free env 1 & 2 or step seq 1/2.

I think you had reached the limit max of Mix values... values between 0.0 and 1.0.
To check, set the mix values to 1.0.
Then chose negative mulitplier in the matrix.

cheers any news on new firmware
thanks again

Just uploaded.
With a new feature from Patrick 

[martindunne]

fantastic

[pld]

Have fun trying out the user patterns, let me know how it goes!

-- Patrick

[martindunne]

hello again
another question, I cannot seem to be able to modulate mix* with free env 1 & 2 or step seq 1/2.

I think you had reached the limit max of Mix values... values between 0.0 and 1.0.
To check, set the mix values to 1.0.
Then chose negative mulitplier in the matrix.

Yep my mistake, i do get a little clipping tho if i set mix values to 0.00 and use env 1/2 and 10.0 multiplier. on env1 clipping starts to occur when the release is at about 0.40 or above.

also when on new user arp page (which is awesome and have had so much fun with it already) and i load another patch it stays on user page when no arp is selected briefly

And could patrick look into the possibilities of an arp step sequencer where for instance you could program it to play user arp 1 four times then user arp 2 three times etc. (with one programmable slot above each encoder ) just an idea.


Xavier : Edited to close the quote

[Xavier]

also when on new user arp page (which is awesome and have had so much fun with it already) and i load another patch it stays on user page when no arp is selected briefly

We discussed that with Patrick.
The other solution would be to change the row but in this case we wouldn't arrive back on the same page after pressing 4 times INST. Even if only one instrument does not have arpegiator enabled.
I think the current behaviour is the better untill a bigger modification that would save the "current row" of each instrument.

[pld]

And could patrick look into the possibilities of an arp step sequencer where for instance you could program it to play user arp 1 four times then user arp 2 three times etc. (with one programmable slot above each encoder ) just an idea.

Heh, I thought briefly about being able to chain patterns but wasn't really sure where to go with it. And I didn't spontaneously have a good plan how to implement it
But I'll give it some thought...

-- Patrick

[matrix12x]

The custom arps are an awesome idea!! great work. I started playing with this right away!

[kuzma_p]

Yes, have to say that firmware goes good route and getting better and better. Thanks!
Would be nice to have access to some arp parameters in mod matrix as destinations. Divider and Duration and Direction for example.

[dimifrag]

Hi Xavier!
When i update the preenfm and start, my default instruments has disappear!
why??
Thanks

[recliq]

What did i lose my settings after flashing the last firmware ?

If a new setting has been added or a setting has been removed, the settings are all reset. You have to change your preference again.