1
preenfm2 and preenfm3 / Re: pfm2 : 2.21
« on: March 26, 2021, 12:41:21 PM »
Superb Thank you 
Great Update
Great Update
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Pages: [1]
2
preenfm2 and preenfm3 / Re: pfm2 : usb midi not working macos 10.10.5
« on: January 16, 2021, 01:10:18 PM »
edit : I seem to have resolved.
I created a 'new configuration' via the audio midi setup and it works fine
happy days.. an OSX rather than a Preen issue by the looks of things
I created a 'new configuration' via the audio midi setup and it works fine
happy days.. an OSX rather than a Preen issue by the looks of things
3
preenfm2 and preenfm3 / [Resolved] pfm2 : usb midi not working macos 10.10.5
« on: January 16, 2021, 12:56:44 PM »
Xavier's note : I've extracted this post from the other thread which was about pfm3.
---------------------------------
I am experiencing this problem as well I am afraid.
Previously my PreenFM2 was working fine via USB. Now it is not recognised as a device in 'audio midi setup' and hence I cannot use the editor or control the Preen from my computer. Most exasperating. Is there anyway to 'reinstall drivers' or anything ? I can enter USB disk mode and copy files across so it's not hardware.
I also have 'USB midi IN/OUT' enabled in the tools menu.
I have tried a number of leads etc and re-booted both the preeen and the computer numerous times.. what else can I try ?
MACOSX 10.10.5
Thanks,
---------------------------------
I am experiencing this problem as well I am afraid.
Previously my PreenFM2 was working fine via USB. Now it is not recognised as a device in 'audio midi setup' and hence I cannot use the editor or control the Preen from my computer. Most exasperating. Is there anyway to 'reinstall drivers' or anything ? I can enter USB disk mode and copy files across so it's not hardware.
I also have 'USB midi IN/OUT' enabled in the tools menu.
I have tried a number of leads etc and re-booted both the preeen and the computer numerous times.. what else can I try ?
MACOSX 10.10.5
Thanks,
4
preenfm2 and preenfm3 / Re: Question Re:midi editing Preen FM2
« on: November 17, 2020, 10:04:19 AM »
Brilliant. Thank you
I understand now !!
A few misunderstandings on my part now rectified.
I understand now !!
A few misunderstandings on my part now rectified.
5
preenfm2 and preenfm3 / Question Re:midi editing Preen FM2
« on: November 15, 2020, 03:56:32 PM »
Hi All,
Just got my Preen FM2.
I love it already., so many possibilities,
I have setup a slightly unusual midi confirguration, and predictably I'm getting some strange behaviour.. also I have a couple of newb questions:
I have a Launch Control connected vis it's USB to a Bome Box, which then sends midi via 5pin din to the Preen FM2.
The bome box also receives midi (midi notes and clock) which it relays (using simple midi in > midi out through route on bome box)
I have different user templates on the Launch Control.
several are just CC values which the bome box passes straight to the preen fm2
Some, though are CC messages which get 'swallowed' by the bome box, converted to NRPN and sent to the Preen Fm (for those parameters not covered by CC)
One in particular (I have assigen to scene 4) is note pitches 1 through 16 for Seq1 .
All works very nicely. 'Opens up' the interface a bit.
However,.. the PreenFM2 is powered by USB connected directly to my mac.
The mac runs the Preen Editor, which if used in isolation also works very nicely. Very useful for envelopes (I love the GUI for that) and selecting modulation sources.
The trouble is that there seems to be a conflict between the Launch Control editor paramters and the Preen Editor.. specifically those NRPN values..
I think this is likely because i have the Preen FM2 to MIDI SEND : CC & NRPN< and MIDI RECEIVE : NRPN as recommended.
I mean I recognise I am trying too hard.. I only really need either the editor, or the launch control..
But I wondered if it is possible to understand a bit more why MID OUT should be set to NRPN and not NRPN & CC ?
Newb question : I only really want to use the Preen as a single voice. I don't have much use for midi timbrality (I have other synths)
Currently I achieve this by setting all instruments to the same midi channel. Is that the right approach ? or should I set common / global channels to something instead of 'off' instead / also ?
Just got my Preen FM2.
I love it already., so many possibilities,
I have setup a slightly unusual midi confirguration, and predictably I'm getting some strange behaviour.. also I have a couple of newb questions:
I have a Launch Control connected vis it's USB to a Bome Box, which then sends midi via 5pin din to the Preen FM2.
The bome box also receives midi (midi notes and clock) which it relays (using simple midi in > midi out through route on bome box)
I have different user templates on the Launch Control.
several are just CC values which the bome box passes straight to the preen fm2
Some, though are CC messages which get 'swallowed' by the bome box, converted to NRPN and sent to the Preen Fm (for those parameters not covered by CC)
One in particular (I have assigen to scene 4) is note pitches 1 through 16 for Seq1 .
All works very nicely. 'Opens up' the interface a bit.
However,.. the PreenFM2 is powered by USB connected directly to my mac.
The mac runs the Preen Editor, which if used in isolation also works very nicely. Very useful for envelopes (I love the GUI for that) and selecting modulation sources.
The trouble is that there seems to be a conflict between the Launch Control editor paramters and the Preen Editor.. specifically those NRPN values..
I think this is likely because i have the Preen FM2 to MIDI SEND : CC & NRPN< and MIDI RECEIVE : NRPN as recommended.
I mean I recognise I am trying too hard.. I only really need either the editor, or the launch control..
But I wondered if it is possible to understand a bit more why MID OUT should be set to NRPN and not NRPN & CC ?
Newb question : I only really want to use the Preen as a single voice. I don't have much use for midi timbrality (I have other synths)
Currently I achieve this by setting all instruments to the same midi channel. Is that the right approach ? or should I set common / global channels to something instead of 'off' instead / also ?
6
preenfm2 and preenfm3 / Re: TX81z W1-W8 + Feedback Waveforms .txt Download
« on: November 08, 2020, 07:40:41 PM »This took a very long time to get right. Considering the TX waveforms are 4096 samples and the PFM2 has a max 1024 samples they aren't 1:1 but sound basically the same.
Enjoy!
Thank You. Really appreciate you sharing these
Pages: [1]